Discussion Forum - Northstar Chevelle Club

Jon H · Jon H

I have a friend I grew up with in northern Minnesota that has a 1950 Lincoln with a 337 CI flat head that Lincoln used in cars from about 1948 through 1951 and then some truck applications. Last year he noticed a lot of coolant leakage and is sure he has a block problem. He tells me these old flat heads are kin...

BB502 · BB502

I need a set of rocker moldings anyone have a new set laying around that they don't need ? Roger 612 483 4827

jim larson · jim larson

Whats the verdict? I've read some posts and most recommend metro. Steel is quite expensive, around $150 for a set. Metro about $110 and soft seal about $90.

gearlube · gearlube

I know about Proven Force, but they are like 2 hours north. Does anyone know of any in the cities?

dashboard · dashboard

I've always wanted a better tool for installing control are bushing, pieces of cut up tailpipe were just a pain. So with my new welding skills that still need refinement, I made this tool. The handle allows for smacking it with a hammer for removal after the bushing has been pressed in. It just makes th...

67ss · 67ss

Went to Wheeler today and ran my engine on the dyno. Went well nothing came apart and made decent numbers. Was hoping for a little more HP but the torque was where I wanted and that will make it a nice street engine. Here are a couple pictures, I'll try and post the video in a bit. -- Edited by 67ss on Wednesd...

SShink · SShink

So I wanted to check the overall health of the mystery 350 SBC motor in my Chevelle, and checked the cranking compression of each cylinder when the engine was cold. After reading more on how to do the cranking check, I realized I was supposed to have taken all of the spark plugs out then install the gauge...

SShink · SShink

Looking for a recommendation on upgrading from front drums to discs. Looking at this Wilwood kit: Wilwood Brake Link I don't want to go any bigger than 12" rotor's to stay within a 17" wheel. Thanks.

John D · John D

Because our Gubmint makes it D*mn-Near-Impossible for a "conscientious/want to do it correctly/I really want to live here - even if I'm married 3-years to a US National" person to wade through the endless "perfectly I-dotted, T-crossed, submitted in Triplicate" flippin' paperwork..

:b...

Lost in the 60s · Lost in the 60s

[IMG]https://i1357.photobucket.com/albums/q752/Stillwat...

jim larson · jim larson

Not a chevelle topic; but a GM product. Any suggestion on how to treat? Thanks

Dave Seitz · Dave Seitz

When I built the shop I used 4ft Fluorescent lights and as time has gone on they have burned out ballasts or gone dim. So along with the smoke and dust from the years shop is getting dark. Of the 16 lights only 3 are working with both bulbs, 4 completely dead, remaining 9 only have one bulb. Cash is a bit tig...

67ss · 67ss

Never seen this one before but I like the fact it uses vehicle speed and a throttle position input to control when the TCC comes on and off. Never used this kit myself but I see their are a few guys swapping in 200 transmission in the near future. Might be something to check into if you are keeping the TCC. ...

Lost in the 60s · Lost in the 60s

New year, may as well get started...

[IMG]https://i1357.photobucket.com/albums/q752/Stillwaterchevs/1962%20Impala%20SS/...

bowtie · bowtie

i missed when it was first announced, but the Car Craft show has moved from WI to KY. I think we'll be seeing more cars again this year.

John D · John D

bowtie · bowtie

Who regularly is on Team Chevelle aka www.chevelles.com? (www.Chevelles.net is an old version of it, btw) I just logged on after 3 months of absence. When I logged in that time, I had to reset my password and never actually ended up surfing. Prior to that, my last post was about 2.5 years ago. Oddly eno...

John D · John D

Mom's moving into a new house end of the month, so I've started to get some of my Shtuff out of there. One of the bigger pita's to move was my Dads Snap-On roller cab & top box. I bought mine in the late '80's, his is from the late '40's. His nickname back in the day was "Stroke"... as he was the guy to go to fo...

Lost in the 60s · Lost in the 60s

I have been trying to find a contact number for them with no luck. Anyone know if they still do this locally ?

John D · John D

jim larson · jim larson

http://www.jegs.com/i/Coker-Tire/257/54890/10002/-1-- Edited by jim larson on Thursday 12th of January 2017 08:43:45 PM

John D · John D

Some people binge-watch cop shows, remodel shows, zombie shows... My bent is stuff like "How it's Made" and things of that nature (I can sit and stare at an automated machine spitting out 100's of pieces per minute in total awe). I came across this and got totally hooked. Clock & Watch making are ab...

67ss · 67ss

On Facebook I found their is a chevelle club in Wisconsin. I made contact with the president of the club yesterday. They have two gatherings they set up in June and August. I will post information on those at a later to see if we can attend. But they are interested in trying to do some club things together f...

67ss · 67ss

Need to learn how to use it, but hoping to weld the brackets on my aluminum radiator for my Chevelle in the near future. -- Edited by 67ss on Saturday 7th of January 2017 03:53:42 PM

Lost in the 60s · Lost in the 60s

The Camaro Club is wondering if we have a date set for the brunch.

jim larson · jim larson

Looks slick. Has anyone used the product? The video's make it look like the clear deal. Thinking of using it on my 2014 Silverado. Take a look. If you have used please comment. https://www.drcolorchip.com/demo/videos.php Can't seem to get this to work as a direct link, can someone fix That?...

Jon H · Jon H

I just breezed through the newsletter and wanted to thank Larry for taking over the job. Also a big thanks to Bryan for all he published! Looking forward to many more.

dashboard · dashboard

Wishing everyone a Merry Christmas from Ohio. Hope to get back to work on the red car after the new year.

Derek69SS · Derek69SS

Welcome Gaston Lee to the family. Mom and baby are both healthy. He is named after a driver who won both the Indy 500 and the AAA championship in 1920, and the younger brother to Louis and Arthur Chevrolet.

69SSConv · 69SSConv

If anyone has a need for some of these, let me know. I needed some for the Blazer project, and the only way I found them was a box of 100 Au-ve-co.

Topic		Started By	Replies	Views	Last Post
	Looking for help with a 1950 Lincoln flat head..... (Preview) I have a friend I grew up with in northern Minnesota that has a 1950 Lincoln with a 337 CI flat head that Lincoln used in cars from about 1948 through 1951 and then some truck applications. Last year he noticed a lot of coolant leakage and is sure he has a block problem. He tells me these old flat heads are kin...	Jon H	18	828	Apr 29, 2017 by Jon H
	67 rocker moldings (Preview) I need a set of rocker moldings anyone have a new set laying around that they don't need ? Roger 612 483 4827	BB502	0	430	Apr 27, 2017 by BB502
	Steel, metro or soft-seal for door weatherstripping? (Preview) Whats the verdict? I've read some posts and most recommend metro. Steel is quite expensive, around $150 for a set. Metro about $110 and soft seal about $90.	jim larson	3	928	Apr 20, 2017 by bowtie
	Anyone know where the drive shaft shops are? (Preview) I know about Proven Force, but they are like 2 hours north. Does anyone know of any in the cities?	gearlube	23	2889	Apr 20, 2017 by jim larson
	A Better Mouse Trap (Preview) I've always wanted a better tool for installing control are bushing, pieces of cut up tailpipe were just a pain. So with my new welding skills that still need refinement, I made this tool. The handle allows for smacking it with a hammer for removal after the bushing has been pressed in. It just makes th...	dashboard	15	1234	Apr 17, 2017 by dashboard
	Had some dyno fun today (Preview) Went to Wheeler today and ran my engine on the dyno. Went well nothing came apart and made decent numbers. Was hoping for a little more HP but the torque was where I wanted and that will make it a nice street engine. Here are a couple pictures, I'll try and post the video in a bit. -- Edited by 67ss on Wednesd...	67ss	7	635	Apr 3, 2017 by 67ss
	Cranking Compression Readings (Preview) So I wanted to check the overall health of the mystery 350 SBC motor in my Chevelle, and checked the cranking compression of each cylinder when the engine was cold. After reading more on how to do the cranking check, I realized I was supposed to have taken all of the spark plugs out then install the gauge...	SShink	29	1109	Apr 2, 2017 by John D
	Derek or other brake experts... (Preview) Looking for a recommendation on upgrading from front drums to discs. Looking at this Wilwood kit: Wilwood Brake Link I don't want to go any bigger than 12" rotor's to stay within a 17" wheel. Thanks.	SShink	8	880	Mar 30, 2017 by Lost in the 60s
	Wanna know why there's so many "Illegal" aliens??... (Preview) Because our Gubmint makes it D*mn-Near-Impossible for a "conscientious/want to do it correctly/I really want to live here - even if I'm married 3-years to a US National" person to wade through the endless "perfectly I-dotted, T-crossed, submitted in Triplicate" flippin' paperwork..:b...	John D	1	566	Mar 30, 2017 by John D
	New body repair tool (Preview) [IMG]https://i1357.photobucket.com/albums/q752/Stillwat...	Lost in the 60s	4	706	Mar 19, 2017 by Lost in the 60s
	This is why you should not order gm chrome running board, any suggestions to repair (Preview) Not a chevelle topic; but a GM product. Any suggestion on how to treat? Thanks	jim larson	12	824	Mar 16, 2017 by jim larson
	Shop lighting (Preview) When I built the shop I used 4ft Fluorescent lights and as time has gone on they have burned out ballasts or gone dim. So along with the smoke and dust from the years shop is getting dark. Of the 16 lights only 3 are working with both bulbs, 4 completely dead, remaining 9 only have one bulb. Cash is a bit tig...	Dave Seitz	0	464	Mar 5, 2017 by Dave Seitz
	Another option for controlling TCC on overdrive transmissions (Preview) Never seen this one before but I like the fact it uses vehicle speed and a throttle position input to control when the TCC comes on and off. Never used this kit myself but I see their are a few guys swapping in 200 transmission in the near future. Might be something to check into if you are keeping the TCC. ...	67ss	11	1050	Mar 1, 2017 by Lost in the 60s
	Been a while since "the addition" kicked in. (Preview) New year, may as well get started...[IMG]https://i1357.photobucket.com/albums/q752/Stillwaterchevs/1962%20Impala%20SS/...	Lost in the 60s	9	924	Feb 24, 2017 by Larry Lucast
	Car Craft show no longer in WI (Preview) i missed when it was first announced, but the Car Craft show has moved from WI to KY. I think we'll be seeing more cars again this year.	bowtie	4	650	Feb 22, 2017 by bowtie
	Red Green's take on fuel systems (Preview)	John D	0	586	Feb 11, 2017 by John D
	Team Chevelle (Preview) Who regularly is on Team Chevelle aka www.chevelles.com? (www.Chevelles.net is an old version of it, btw) I just logged on after 3 months of absence. When I logged in that time, I had to reset my password and never actually ended up surfing. Prior to that, my last post was about 2.5 years ago. Oddly eno...	bowtie	11	2123	Feb 4, 2017 by 4-door Chevelle
	Goin' on 70 and still on the job... (Preview) Mom's moving into a new house end of the month, so I've started to get some of my Shtuff out of there. One of the bigger pita's to move was my Dads Snap-On roller cab & top box. I bought mine in the late '80's, his is from the late '40's. His nickname back in the day was "Stroke"... as he was the guy to go to fo...	John D	3	727	Jan 31, 2017 by Lost in the 60s
	How to contact Keystone bumper re-plating (Preview) I have been trying to find a contact number for them with no luck. Anyone know if they still do this locally ?	Lost in the 60s	14	1916	Jan 28, 2017 by Jon H
	Aussie's and a '69 (Preview)	John D	1	714	Jan 28, 2017 by BLyke
	Best appearing bias tire that is a radial (Preview) http://www.jegs.com/i/Coker-Tire/257/54890/10002/-1-- Edited by jim larson on Thursday 12th of January 2017 08:43:45 PM	jim larson	1	693	Jan 12, 2017 by Derek69SS
	Micro-Machining "porn"... (Preview) Some people binge-watch cop shows, remodel shows, zombie shows... My bent is stuff like "How it's Made" and things of that nature (I can sit and stare at an automated machine spitting out 100's of pieces per minute in total awe). I came across this and got totally hooked. Clock & Watch making are ab...	John D	3	631	Jan 11, 2017 by dashboard
	Wisconsin chevelle club (Preview) On Facebook I found their is a chevelle club in Wisconsin. I made contact with the president of the club yesterday. They have two gatherings they set up in June and August. I will post information on those at a later to see if we can attend. But they are interested in trying to do some club things together f...	67ss	7	1723	Jan 9, 2017 by jim larson
	Bought a late Christmas present for myself. (Preview) Need to learn how to use it, but hoping to weld the brackets on my aluminum radiator for my Chevelle in the near future. -- Edited by 67ss on Saturday 7th of January 2017 03:53:42 PM	67ss	4	670	Jan 9, 2017 by Lost in the 60s
	Bow Tie Brunch date set ? (Preview) The Camaro Club is wondering if we have a date set for the brunch.	Lost in the 60s	3	644	Jan 9, 2017 by Tanaman
	Doctor Color Chip kit? (Preview) Looks slick. Has anyone used the product? The video's make it look like the clear deal. Thinking of using it on my 2014 Silverado. Take a look. If you have used please comment. https://www.drcolorchip.com/demo/videos.php Can't seem to get this to work as a direct link, can someone fix That?...	jim larson	1	658	Jan 4, 2017 by dashboard
	New newsletter editor....Thank you Larry. (Preview) I just breezed through the newsletter and wanted to thank Larry for taking over the job. Also a big thanks to Bryan for all he published! Looking forward to many more.	Jon H	4	524	Dec 27, 2016 by Chris R
	Merry Christmas (Preview) Wishing everyone a Merry Christmas from Ohio. Hope to get back to work on the red car after the new year.	dashboard	10	778	Dec 25, 2016 by John D
	New addition to the family! (Preview) Welcome Gaston Lee to the family. Mom and baby are both healthy. He is named after a driver who won both the Indy 500 and the AAA championship in 1920, and the younger brother to Louis and Arthur Chevrolet.	Derek69SS	23	965	Dec 15, 2016 by Derek69SS
	Radiator Shroud Clips (Preview) If anyone has a need for some of these, let me know. I needed some for the Blazer project, and the only way I found them was a box of 100 Au-ve-co.	69SSConv	5	678	Dec 12, 2016 by 69SSConv
«First < 1 … 16 17 18 19 20 … 68 > Last» \| Page of 68 sorted by