Discussion Forum - Northstar Chevelle Club

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: How difficult is it to bend and make a new fuel line?


2K+ Club

Status: Offline
Posts: 2734
Date:
How difficult is it to bend and make a new fuel line?
Permalink  
 


Currently I have the body up and off the frame of my 66. I noticed the fuel line is a little rusted where it runs up and over the frame. I could clean it up and put some rust converter on it; but think it may be better to replace the line now as on a 66 you have to raise the body off the frame to replace the fuel line.

i guess Inline Tube makes the best replacement for around $90 or $$120 with shipping depending if you want OEM steel or stainless.  I was thinking of just buying the materials and use the old line to make the proper bends.  I can remove the old line intact as the body in high enough off the frame. If you buy from inline or anyone else they bend the line in half and still charge you oversized for shipping.

Would this be a good idea?  Have any of you guys done this?



-- Edited by jim larson on Monday 18th of December 2017 01:10:56 PM

__________________

Jim L

Lake City



Founding Member

Status: Offline
Posts: 2787
Date:
Permalink  
 

If you use Nickel/Copper alloy lines, they bend easy by hand and will last forever.

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project



2K+ Club

Status: Offline
Posts: 2734
Date:
Permalink  
 

Thanks Dereck, I see it’sabout $50 for25’.  I think I will pull my old line for a more through inspection 



__________________

Jim L

Lake City



1K+ Club

Status: Offline
Posts: 1196
Date:
Permalink  
 

whewReplacement lines have protective cover in certain areas to match factory install.
Have one laying on the white elky frame, not yet installed.
If I think of it I will snap photo.
White elky line was actually worn through over axel area where body sagged on old mounts.
Lucky the car didn't burn up.whew



__________________

More ambition than brains,

If you have more than 5 of anything, best to stop counting!



2K+ Club

Status: Offline
Posts: 2734
Date:
Permalink  
 

The axel area is the only area I have any rust.  I installed a  bushing in the spot just in front of the rear wheels ( sometimes not installed there at the factory), that should help with rubbing.  I was planning on using the factory spring steel guards from ooriginal fuel line.  I got a response from Inline tube and the fuel line they sell through Amazon is the same line they use on there preformed lines.



__________________

Jim L

Lake City



1K+ Club

Status: Offline
Posts: 1196
Date:
Permalink  
 

IMG_4176.JPGIMG_4177.JPGIMG_4178.JPGIMG_4179.JPGIMG_4180.JPGIMG_4181.JPG

Looks like two areas with armor, 1 steel, one some type of fabric loaded with asphalt like material.

Not easy to transfer or fabricate.

How much to ship?

Karl



Attachments
__________________

More ambition than brains,

If you have more than 5 of anything, best to stop counting!



Founding Member

Status: Offline
Posts: 2787
Date:
Permalink  
 

Good thing those lines aren't under pressure!

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project



1K+ Club

Status: Offline
Posts: 1196
Date:
Permalink  
 

Lousy mileage, fuel smell, probably fuel starved too.
Exhaust was full of holes back there too.
We were both pretty lucky that car did not burn up.

Sucking air, bleeding fuel, lucky gravity exists as that hole is at the highest elevation in the line.

whew

Karl



__________________

More ambition than brains,

If you have more than 5 of anything, best to stop counting!



2K+ Club

Status: Offline
Posts: 2734
Date:
Permalink  
 

Well I ordered a new line from the right stuff,  for the price $61 plus some other things I bought I got free shipping.

Decided to go with the OEM steel line, supposed to be pre- formed as origional with guards  and barbed ends as the came in 65.   In searching on line it seem you should clean with lacquer and paint with clear engine enamel. Kevin painted his new line with clear lacquer.



__________________

Jim L

Lake City

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Chatbox
Please log in to join the chat!