Discussion Forum - Northstar Chevelle Club

Members Login
Username 
 
Password 
    Remember Me  
NCC Forum Home Page -> NCC - Projects and Updates -> Got one seat in!
Post Info TOPIC: Got one seat in!
bowtie


Secretary

Status: Offline
Posts: 2988
Date:
Got one seat in!
Permalink  
 

I didn't have a lot of time today, but I finally got the driver's seat in. Had to re-trim the carpet some and make some new holes, then mount the brackets. The seats sit higher than my other ones, hope they settle down some, my head just touches the headliner and that's with the seats at their lowest mounting height. Hopefully tomorrow I can get the other one mounted and in, then put the shoulder harnesses in. Next up is a smaller steering wheel which will help with the seat height/knee clearance. No good pics yet. 



__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
bowtie


Secretary

Status: Offline
Posts: 2988
Date:
Permalink  
 





I still have some little stuff to do like put the sunvisors back in, hang the driver's door panel, attach the concole again, and swap to a smaller steering wheel, but it's ready to rock!

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
steve m


Member

Status: Offline
Posts: 81
Date:
Permalink  
 

Is that carpet of out a 69 chevelle?, Just put in new headrests on my 67 SS427 impala, Not sure if I like them yet. These repos look just like the originals.



Attachments
__________________

steve marier  maplewood, mn
bowtie


Secretary

Status: Offline
Posts: 2988
Date:
Permalink  
 

Yep, same stuff I got from you. The rear never did get installed until this week. Fit good with some additional trimming around my shifter and bolt holes. I do need to fill in a section where it was mysteriously hacked out before i got it.

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
bowtie


Secretary

Status: Offline
Posts: 2988
Date:
Permalink  
 



I even was able to pactch in some of the missing carpet pieces. Obvious if you're looking, but good enough for a glance. Just need to color my kick panels black.



-- Edited by bowtie on Sunday 24th of April 2011 04:47:58 PM

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
SShink


3K+ Club

Status: Offline
Posts: 4764
Date:
Permalink  
 

That's progress man!!! 



__________________

Stan S.-Twin Cities 'South Metro'

1972 Malibu Convertible 2nd time around 

1999 SS Camaro LS1-6 speed

Forum influenced terms: 'Link Paste', 'Stanitized', & 'Revolving garage door...' 

 
Lost in the 60s


President

Status: Offline
Posts: 7258
Date:
Permalink  
 

Those buckets look like they belong in there....  Ev en the pleats run the same direction as the rear seat. Very clean !!



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

Some Assembly Required

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS 350 rs
Chris R


2K+ Club

Status: Offline
Posts: 2761
Date:
Permalink  
 

Wow. That does look very nice.



__________________

Chris - Ramsey, MN.

Dear Optimist, Pessimist, and Realist.

While you guys were busy arguing about the glass of water. I drank it!

Sincerly,

The opportunist.
bowtie


Secretary

Status: Offline
Posts: 2988
Date:
Permalink  
 

The only disappointment is that the seats, front belts and wheel look newer than the rest

Oh yeah, they're just about the only new pieces in there.



__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
Lost in the 60s


President

Status: Offline
Posts: 7258
Date:
Permalink  
 

bowtie wrote:

The only disappointment is that the seats, front belts and wheel look newer than the rest

Take some course scotchbright and scuff them up....

 

 



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

Some Assembly Required

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS 350 rs
bowtie


Secretary

Status: Offline
Posts: 2988
Date:
Permalink  
 

Yeah, then they'll match the outside of the car!

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
Chris R


2K+ Club

Status: Offline
Posts: 2761
Date:
Permalink  
 

Were you still thinking of having it professional buffed during a club meeting?



__________________

Chris - Ramsey, MN.

Dear Optimist, Pessimist, and Realist.

While you guys were busy arguing about the glass of water. I drank it!

Sincerly,

The opportunist.
bowtie


Secretary

Status: Offline
Posts: 2988
Date:
Permalink  
 

Yeah, might not have the funds right now unless they want to show the how-to in exchange for the what-on.

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
NCC Forum Home Page -> NCC - Projects and Updates -> Got one seat in!
Chatbox
Please log in to join the chat!