Discussion Forum - Northstar Chevelle Club

Members Login
Username 
 
Password 
    Remember Me  
NCC Forum Home Page -> NCC - General Discussion -> Borrowed pushrod
Post Info TOPIC: Borrowed pushrod
67ss


1K+ Club

Status: Offline
Posts: 1724
Date:
Borrowed pushrod
Permalink  
 

So what happened with the 454 that had the bad pushrod from the picnic? Anybody heard if he pulled the engine down to see what was going on.

__________________

Chris P
East Central, Mn

66 Chevelle 300 deluxe
John D


2K+ Club

Status: Offline
Posts: 2791
Date:
Permalink  
 

We'll be installing new pushrods & rockers this Saturday... so we'll see if any others are showing signs of failure, or if it was a fluke with just one that was bad.

(You need the loaner back??)

__________________

 

John D. - St. Louis Park, MN.

1965 El Camino - LT-1, 4L60e, 4wh discs, SC&C susp.
2013 F-150 Platinum - Twin Turbo 3.5

2018 Factory Five MkIV Roadster build thread
67ss


1K+ Club

Status: Offline
Posts: 1724
Date:
Permalink  
 

I will need the loaner back at some point in time. You can give it to bryan when you are done with it if you happen to see him at one of the monthly meetings and I can grab it from him later.

Are you going to check lobe lift to see if the cam is damaged. I thought it still had a miss in it after installing the pushrod?

__________________

Chris P
East Central, Mn

66 Chevelle 300 deluxe
John D


2K+ Club

Status: Offline
Posts: 2791
Date:
Permalink  
 

Yup, we'll be checking (if I can find my "big" dial indicator...). If not, we'll use the "little" one and compare other lobes at the end/top of the lobe.

The miss cleared up on the drive home that day - I'm guessing it was loaded up, and he did find a cooked plug wire.

__________________

 

John D. - St. Louis Park, MN.

1965 El Camino - LT-1, 4L60e, 4wh discs, SC&C susp.
2013 F-150 Platinum - Twin Turbo 3.5

2018 Factory Five MkIV Roadster build thread
Chris R


2K+ Club

Status: Offline
Posts: 2745
Date:
Permalink  
 

I was going to say. He definitely had a spark plug boot that was burnt against the header pipe on one cylinder.

Did you guys swap or fix the rearend on that 55 yet? Winter project?

__________________

Chris - Ramsey, MN.

Dear Optimist, Pessimist, and Realist.

While you guys were busy arguing about the glass of water. I drank it!

Sincerly,

The opportunist.
67ss


1K+ Club

Status: Offline
Posts: 1724
Date:
Permalink  
 

We did find a rear end for the 55, it is out of a 74 nova. Probably won't put it in until spring at this point.

Trying to work on the 396 for his chevelle at the moment. Got it back from the machine shop going to start assembling the short block here soon.

__________________

Chris P
East Central, Mn

66 Chevelle 300 deluxe
67ss


1K+ Club

Status: Offline
Posts: 1724
Date:
Permalink  
 

So how did it turn out John, was the cam OK? I would imagine you put some roller rockers on it.

__________________

Chris P
East Central, Mn

66 Chevelle 300 deluxe
John D


2K+ Club

Status: Offline
Posts: 2791
Date:
Permalink  
 

Snafu...
- Craig ordered a set of stock replacement pushrods from the local auto parts store. They arrive, he gets 'em home, opens the box, and they're USED. Some A-hole put their used rods in the box and then returned them - nobody checked and they didn't get caught.
- So, he orders a set from Jegs. They arrive. Come saturday morning I get there and he's got 'em cleaned up, blown out, and oiled... ready to go. Except they're 3/8". The guideplates are 5/16".
- Spend 1-1/2 hours on the 'net & phone trying to find either a set of 3/8" guideplates, or a set of 5/16" pushrods. Nobody's got 'em in stock, or within an hour's drive. The unanimous decision was "Screw This" and go have some lunch.

So, it's still where it was. It's either gonna get new 5/16" pushrods, or new guideplates. I haven't talked to Craig since the weekend.

__________________

 

John D. - St. Louis Park, MN.

1965 El Camino - LT-1, 4L60e, 4wh discs, SC&C susp.
2013 F-150 Platinum - Twin Turbo 3.5

2018 Factory Five MkIV Roadster build thread
Chris R


2K+ Club

Status: Offline
Posts: 2745
Date:
Permalink  
 

My suggestion would be to just go to Gary Heddon at Magnum superchargers or Wheeler and just get a set from them if thats the case. This way he knows for sure what he is getting is the stuff he needs.

I needed a set of brand new lifters a few years ago when I had Magnum go through the heads on my 396. I didnt want to deal with the same experience Craig is going through so I just got the set from Gary instead. An engine builder will know exactly what rods he needs.



__________________

Chris - Ramsey, MN.

Dear Optimist, Pessimist, and Realist.

While you guys were busy arguing about the glass of water. I drank it!

Sincerly,

The opportunist.
bowtie


Secretary

Status: Offline
Posts: 2940
Date:
Permalink  
 

I have your pushrod. it's in my lunch bag now.

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
Chris R


2K+ Club

Status: Offline
Posts: 2745
Date:
Permalink  
 

Really. I thought most people bring a sandwich to work for lunch. Let us know how it tastes.



__________________

Chris - Ramsey, MN.

Dear Optimist, Pessimist, and Realist.

While you guys were busy arguing about the glass of water. I drank it!

Sincerly,

The opportunist.
bowtie


Secretary

Status: Offline
Posts: 2940
Date:
Permalink  
 

irony

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
NCC Forum Home Page -> NCC - General Discussion -> Borrowed pushrod
Chatbox
Please log in to join the chat!