Discussion Forum - Northstar Chevelle Club

Members Login
Username 
 
Password 
    Remember Me  
NCC Forum Home Page -> NCC - General Discussion -> Seat Belts
Post Info TOPIC: Seat Belts
MN JIM


Contributor

Status: Offline
Posts: 23
Date:
Seat Belts
Permalink  
 

I bought some replacement seat belts because my car didn't have any installed when I bought it. The originals came with the car but are in pretty bad shape.

The guy I bought it from put new carpet in and didn't cut any holes for the seat belts so I can't tell where the mouting points are. I hate to just start hacking on the carpet. Can someone help with a location? I have a bench seat so maybe reference the seat mounting bolt.

By the way I was at a car show in Redwing yesterday. Seen a very nice white 1970 396 SS. Does that belong to anyone in the group?

Thanks

Jim


__________________
John D


2K+ Club

Status: Offline
Posts: 2791
Date:
Permalink  
 

Down & dirty/Quick & Easy...

Get some long finishing nails & your jack. (Using all safety precautions...) Jack up one side of the car, crawl under and you'll see the threaded lugs sticking into the driveshaft tunnel. Poke a finishing nail through the hole into the car - find it on the inside.

For the outboard belts, removing the sill plate is the easiest way to find the holes.

__________________

 

John D. - St. Louis Park, MN.

1965 El Camino - LT-1, 4L60e, 4wh discs, SC&C susp.
2013 F-150 Platinum - Twin Turbo 3.5

2018 Factory Five MkIV Roadster build thread
bowtie


Secretary

Status: Offline
Posts: 2940
Date:
Permalink  
 

Use a very sharp blade and cut a small X instead of just drilling into the carpet too. Drilling can make you catch a thread and rip into the carpet.

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more
MN JIM


Contributor

Status: Offline
Posts: 23
Date:
Permalink  
 

Thanks for the info. I will give it a try.

Jim

__________________
SShink


3K+ Club

Status: Offline
Posts: 4731
Date:
Permalink  
 

Rather than jacking up the car, IMO opinion it's easier to remove the bench seat (4 bolts) and pull the carpet up to find the hole locations.  Then you can install the bolts, lay the carpet back down, and then cut an X where the bolt is when you press down on the carpet.

I saw a yellow and black stripe '72 Chevelle at Hastings last night and I thought it might be you, but probably not since you were at Redwing.

__________________

Stan S.-Twin Cities 'South Metro'

1972 Malibu Convertible 2nd time around 

2001 Mustang GT Convertible 

Forum influenced terms: 'Link Paste', 'Stanitized', & 'Revolving garage door...' 

 
MN JIM


Contributor

Status: Offline
Posts: 23
Date:
Permalink  
 

Finaly had time to take Stan's advice and pulled the bench seat. Now I really feel dumb. There are two holed near the drive shaft hump. Right size holes for the belt bolt but no weld nut on the pan. No big deal. So I start to look for the outward holes. Not there! The inboard holes are about an inch forward of the seat bolts. Can someone tell me how far from the inboard hole the outward hole should be?

__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
NCC Forum Home Page -> NCC - General Discussion -> Seat Belts
Chatbox
Please log in to join the chat!