Looking for an older Edelbrock C-396 intake for a Holley with oval port heads.
jim larson said
Jun 5, 2013
Anyone have one of these or know of a possible source?
Lost in the 60s said
Jun 5, 2013
There's one on ebay for $125 shipped.
jim larson said
Jun 5, 2013
Lost in the 60s wrote:
There's one on ebay for $125 shipped.
Didn't see that one when looking yesterday. Was it for a BBC and a holley as opposed to a carter?
dashboard said
Jun 5, 2013
Give Leo a call, I'll bet he has one.......or two ......or three.
more ambition than brains said
Jun 5, 2013
I have the one off Biskwik- Edelbrock Big Block Holly intake. Pretty sure it is oval ports, was a peanut port motor.
Has been all cleaned up.
Have some pretty cool tall valve covers from that motor. Also have another one sitting on a 396 motor in storage.
Karl
612-384-5477
jim larson said
Jun 5, 2013
more ambition than brains wrote:
I have the one off Biskwik- Edelbrock Big Block Holly intake. Pretty sure it is oval ports, was a peanut port motor.
Has been all cleaned up.
Have some pretty cool tall valve covers from that motor. Also have another one sitting on a 396 motor in storage.
Karl
612-384-5477
Hi Karl, I don't know for sure what I am looking for, a friend is helping me out and going to send some photo's. The one I am looking for should should be an older intake have the water exit ports in the same location as the cast iron Holley Intake. Not sure what this means; but think it means the location for the heater hose and return for the water pump.
Lost in the 60s said
Jun 5, 2013
jim larson wrote:
Lost in the 60s wrote:
There's one on ebay for $125 shipped.
Didn't see that one when looking yesterday. Was it for a BBC and a holley as opposed to a carter?
It appeared to have mulitple carb mounting positions. The auction only had 15 hrs left when I posted Tuesday night and it is gone now. I neglected to put it in my watched folder for later access to the pic.
CDNSS said
Jun 5, 2013
the c396 is an oval port intake drilled for holley and afb ..........I dont recall the heater hose location is same as stock intake ........the stock iron intake works just as good to 5500..........if you want a correct location alum intake get a L78 063 intake bolt it on your oval heads and go, good intake look stock painted orange gm snowflake etcetc
jim larson said
Jun 6, 2013
CDNSS wrote:
the c396 is an oval port intake drilled for holley and afb ..........I dont recall the heater hose location is same as stock intake ........the stock iron intake works just as good to 5500..........if you want a correct location alum intake get a L78 063 intake bolt it on your oval heads and go, good intake look stock painted orange gm snowflake etcetc
Bill, I am sending you photo's of the carb and the intake.
more ambition than brains said
Jun 6, 2013
Sorry, mine is a Performer 2 Can take a spread bore (quadrajet) or with an adapter a holly.
Anyone have one of these or know of a possible source?
There's one on ebay for $125 shipped.
Didn't see that one when looking yesterday. Was it for a BBC and a holley as opposed to a carter?
I have the one off Biskwik- Edelbrock Big Block Holly intake. Pretty sure it is oval ports, was a peanut port motor.
Has been all cleaned up.
Have some pretty cool tall valve covers from that motor. Also have another one sitting on a 396 motor in storage.
Karl
612-384-5477
Hi Karl, I don't know for sure what I am looking for, a friend is helping me out and going to send some photo's. The one I am looking for should should be an older intake have the water exit ports in the same location as the cast iron Holley Intake. Not sure what this means; but think it means the location for the heater hose and return for the water pump.
It appeared to have mulitple carb mounting positions. The auction only had 15 hrs left when I posted Tuesday night and it is gone now. I neglected to put it in my watched folder for later access to the pic.
Bill, I am sending you photo's of the carb and the intake.
Sorry, mine is a Performer 2 Can take a spread bore (quadrajet) or with an adapter a holly.
Karl