Decided I need to make room in the storage shed if I'm going to fit the car in there this winter. I can bring stuff to the meeting on the 19th. Everything is best offer and has to go.
Autometer gauges- all are 2 5/8" electric Ultra lights. Gauges and red & green bulb covers. 1/2 price of new.
#4427 Oil Pressure $40
#4491 Volt Gauge $25
#4437 Water Temp $35
Summit 3 3/4" 10,000 rpm tach with shift light in the face $25
All four gauges $100
Holley Carb Parts $30 for all:
(3) power Valves (7.5,8.5,9.5)
(3) Accelerator Pump Discharge Nozzels (25,28,31)
Assortment of Accelerator Cams
Manual Choke Lever
MAKE AN OFFER:
(3) inside AC/Heater boxes - one still has heater control attached
(3) Outside AC boxes - All have POA valves 1 missing Fan, one evaporator is marked 1996
Balancer & Flywheel from 1pcs rear main 350 (external balanced?)
'72 Monte Belts -some buckels broken
'72 Chevelle Front belts- driver & passenger lap only
SB 'Bowtie Sparkplug wire looms
Taylor Spiro Pro 8mm Wires SB length - Basically New
'70-'72 Dash Pad Driver quality (fixed in the corner)
'72 Coupe Black Carpet. A little bit of fade on center hump (picture looks worse than installed in the car)
'72 Coupe door panels (Aftermarket dated 1996) Driver side missing dual chrome stripes
'72 Sweep Dash Shell
Pair of New Parking brake cables for rear disk swap caddy brakes (these are the one's John D list in the 'tips" section)
'72 Bench Seat. Cover is in good shape, but it isn't the correct pattern. The picture show a mark on the drives side where the dash was sitting on it. Should come out.
Light duty Mig Welder car from Northern. Has holder for bottle, need to have the bolts tightened up.
Lots of various AC Duct work, Hoses, Etc. From 70-72 Monte & Chevelles
-- Edited by SteveS on Wednesday 9th of November 2011 09:18:01 PM
Pushrod said
Nov 9, 2011
hey steve ill take the dash shell and the ac stuff if you want to bring them, is the shell cracked at all or is it something that can be fixed? THX!
SteveS said
Nov 9, 2011
I don't remember any cracks, I will check it out. The radio has been cut out for a DIN style if that makes a difference?
Bowtieman427 said
Nov 9, 2011
Hey Steve is there a good time to head down and check out what you have ?? Maybe Sat ? There is so much there I am interested in. Holley Carb Parts $30 for all:
(3) power Valves (7.5,8.5,9.5)
(3) Accelerator Pump Discharge Nozzels (25,28,31)
Assortment of Accelerator Cams
Do you have have jets ???
Fo starters.
I want to check out the seat belts and welding cart.
And odd and ends things that may be needed.
IF I were to do a rear disc brake converstion on a '59 or 67 Impala would those cables work ?
-- Edited by Bowtieman427 on Thursday 10th of November 2011 12:07:15 AM
-- Edited by Bowtieman427 on Thursday 10th of November 2011 12:20:52 AM
SteveS said
Nov 10, 2011
I'll give you a call Jim.
Enganeer said
Nov 10, 2011
Steve,
I am interested in all four gauges for $100. Do they come with senders? Are you going to the meeting next week?
Let me know what you want for the hei? I would like a spare as backup.
SteveS said
Nov 10, 2011
John- The Gauges should be complete with senders, and I have a chrome 3 gauge panel they go into if you want it. I can bring them to the meeting. As for the HEI, how about $10 or $15 if you want the unopened MSD HEI spring & weight advance kit?
-- Edited by SteveS on Thursday 10th of November 2011 01:00:07 PM
Enganeer said
Nov 10, 2011
Steve,
Bring the panel also and I'll take the hei with the spring kit.
Decided I need to make room in the storage shed if I'm going to fit the car in there this winter. I can bring stuff to the meeting on the 19th. Everything is best offer and has to go.
Autometer gauges- all are 2 5/8" electric Ultra lights. Gauges and red & green bulb covers. 1/2 price of new.
#4427 Oil Pressure $40
#4491 Volt Gauge $25
#4437 Water Temp $35
Summit 3 3/4" 10,000 rpm tach with shift light in the face $25
All four gauges $100
Holley Carb Parts $30 for all:
(3) power Valves (7.5,8.5,9.5)
(3) Accelerator Pump Discharge Nozzels (25,28,31)
Assortment of Accelerator Cams
Manual Choke Lever
MAKE AN OFFER:
(3) inside AC/Heater boxes - one still has heater control attached
(3) Outside AC boxes - All have POA valves 1 missing Fan, one evaporator is marked 1996
'72 monte dash wiring harness & fuse box
'72 Chevelle sweep gauge
Starter
HEI
MSD HEI Advance Kit unopened
Original '72 small block brackets
'70-72 SS gauge cluster lens - light scratches, maybe buff out?
Balancer & Flywheel from 1pcs rear main 350 (external balanced?)
'72 Monte Belts -some buckels broken
'72 Chevelle Front belts- driver & passenger lap only
SB 'Bowtie Sparkplug wire looms
Taylor Spiro Pro 8mm Wires SB length - Basically New
'70-'72 Dash Pad Driver quality (fixed in the corner)
'72 Coupe Black Carpet. A little bit of fade on center hump (picture looks worse than installed in the car)
'72 Coupe door panels (Aftermarket dated 1996) Driver side missing dual chrome stripes
'72 Sweep Dash Shell
Pair of New Parking brake cables for rear disk swap caddy brakes (these are the one's John D list in the 'tips" section)
'72 Bench Seat. Cover is in good shape, but it isn't the correct pattern. The picture show a mark on the drives side where the dash was sitting on it. Should come out.
Light duty Mig Welder car from Northern. Has holder for bottle, need to have the bolts tightened up.
Lots of various AC Duct work, Hoses, Etc. From 70-72 Monte & Chevelles
PICS OF EVERYTHING HERE:
https://s469.photobucket.com/albums/rr60/sbsrkh1/For%20Sale/
-- Edited by SteveS on Wednesday 9th of November 2011 09:18:01 PM
hey steve ill take the dash shell and the ac stuff if you want to bring them, is the shell cracked at all or is it something that can be fixed? THX!
Hey Steve is there a good time to head down and check out what you have ?? Maybe Sat ? There is so much there I am interested in.
Holley Carb Parts $30 for all:
(3) power Valves (7.5,8.5,9.5)
(3) Accelerator Pump Discharge Nozzels (25,28,31)
Assortment of Accelerator Cams
Do you have have jets ???
Fo starters.
I want to check out the seat belts and welding cart.
And odd and ends things that may be needed.
IF I were to do a rear disc brake converstion on a '59 or 67 Impala would those cables work ?
-- Edited by Bowtieman427 on Thursday 10th of November 2011 12:07:15 AM
-- Edited by Bowtieman427 on Thursday 10th of November 2011 12:20:52 AM
I am interested in all four gauges for $100. Do they come with senders? Are you going to the meeting next week?
Let me know what you want for the hei? I would like a spare as backup.
John-
The Gauges should be complete with senders, and I have a chrome 3 gauge panel they go into if you want it. I can bring them to the meeting. As for the HEI, how about $10 or $15 if you want the unopened MSD HEI spring & weight advance kit?
-- Edited by SteveS on Thursday 10th of November 2011 01:00:07 PM
Bring the panel also and I'll take the hei with the spring kit.
din hole is fine will you bring to meeting ?